FASTFRAME-CB PCMCIA BOARD
Alacron introduces the FastFrame-CB. Available in both analog, digital, and camera link configurations for greater flexibility and cost savings. The FastFrame-CB uses the Nexperia (formerly TriMedia) PNX1302 microprocessor from Philips Semiconductors.
The Philips PNX1302 Processor
The Philips developed PNX1302 is a high-performance programmable single-chip processor that delivers real-time processing of audio, video, graphics, and communications datastreams. The TriMedia TM1302 employs a typical Very Long Instruction Word (VLIW) architecture capable of 720 MFLOPS/900 MIPS peak and has a 32-bit CPU that connects instruction and data caches at rates of 4 GB/sec and 1100MB/sec peak. By incorporating the TriMedia processor into Alacron’s new FastImage, customers and developers can significantly increase their processing power enabling them to work more efficiently and cost effectively.
Click below to Download DataSheet
PNX1300
Datasheet (
409 KB)
FastFrame-CB Features
- PCMCIA board with one TriMedia processor with 16 MB of dedicated high speed (572MB/s) SDRAM, capable of over 720 MFLOPS of computational power
- Collects NTSC/PAL/SECAM data from up to four digital cameras
- Digital capture, 32 data bits (RS-422, LVDS) with control and clock
- One 85 MHz Camera Link (Channel Link) inputs
- Programmable FPGAs for I/O interface configuration
- 32 bit cardbus
- Supported by standard software development tools, including fully optimized microcoded signal and image processing libraries (FOIL)
- Optional TriMedia software development environment (SDE) for Windows® 9X/NT/2K and Solaris™ and Linux
Camera Link Specification(287MB)
National Semiconductor
Channel Link Datasheet (
343 KB)
Technical Specifications
 Block Diagram |
| NTSC/PAL Composite Video Capture (1 channel/4:1 Mux) | |
| Input levels | 1V peak-to-peak nom., 0.3 to 1.2V peak-to-peak max. |
| Input impedance | 75 Ohms |
| Channel crosstalk | -50 dB max. |
| Resolution | 8 bits |
| Formats supported | PAL BGHI, PAL N, PAL M, NTSC M, NTSC N, NTSC 4.43, NTSC-Japan, SECAM |
| Digital Video Capture | |
| Common mode input range | -5V
to +5V (0 to 2.4V with LVDS option) |
| Input sensitivity | 250mV
differential (100mV with LVDS option) |
| Input hysteresis | 50 mV typical |
| Max. clock rate | 80 MHz |
| Max. input data width | 32 bits |
| Formats supported | ITU-R
BT.656 (4:2:2 interlaced color), 8/10-bit mono. variable/line scan, 8/10-bit raw data, 8/10-bit RGB,16-bit raw at 20 MHz (40 MB/sec.) |
| Input Levels | RS-422, LVDS signaling |
| Camera Control | |
| Serial port | Asynchronous RS-232, 600-19,200 Baud |
| Frame/line start outputs | 2 RS-422 |
| Exposure control out. | 2 RS-422 |
| Master clock out. | 2 RS-422 programmable in 0.07 Hz steps up to 40 MHz |
| General purpose out. | 4 RS-422 |
| Pixel clock inputs | 2 RS-422 |
| Line/frame valid in. | 4 RS-422 |
| External trigger in. | 2 RS-422 |
| Gen. purpose in. | 4 RS-422 |
| Power | No camera power provided by card; use an external supply |
| RS-422 input | RS-422, LVDS signaling |
| PCI Interface | |
| Clock rate | 33 MHz max. |
| Data width | 64/32 bits |
| Peak DMA rate | 256/132 MB/sec. |
| Standards compliance | PCI Rev. 2.1 |
Click below to Download DataSheet or Register to Download Manuals
FastFrame-CB
Frame Grabber(
222 KB)
