FAST-X SERIES BOARDS

FAST-X PCI-X BOARDS

INTRODUCTION

The Fast-X frame grabber series is for users who anticipate a demand for extreme I/O requirements or higher bandwidth, complex image processing and real-time fast storage in a cost effective platform. The base Fast-X, is a one-half raw-length PCI board with four GigE ports and/or three basic 85 MHz Camera Link Channels and more which provide input for the newest cameras as well as a header for adaptation of other high speed FastXinterfaces. The front end data is formatted and preprocessed by a FPGA before being sent to the memory subsection, processor, GigE interfaces or other outputs. Finally, the Fast-X interfaces to the host computer through a PCI-X or PCIe interface for state-of-the-art data acquisition. Options include the addition of multiple(8) Serial ATA (SATA) 150 MB/sec interfaces for continuous high-speed data storage without the usual OS or PCI transfer delays.

FAST-X KEY SERIES FEATURES

The diagram below outlines the basic functional section of the FAST-X boards. These are:

  • One half raw PCI form factor board with 1-2 GB dedicated high speed DDRAM for sustained real-time on-board storage
  • Collects data from up to three asynchronous basic Camera (channel) Link channels
  • Camera Link Specification

    National Semiconductor Channel Link Datasheet (343 KB)

  • Programmable FPGA and memory subsystem for I/O interface configuration and processing
  • STRETCH 5610 configurable processor for processing, strage, GigE connectivity and PCI-X interface
  • PCI-X bus interface with 32/64 bit downward compatibility
  • Supported by standard firmware development tools, including fully optimized basic data manipulation, data formatting and image processing routines
  • Drivers for Windows® 2K/XP, Linux, and Solaris™

Fast-X PCI-X frame Grabber

OPTIONS

  • Four GigE I/O ports
  • UXGA two channel (four channel muxed) 205 MHz convertors
  • Six Basic Camera Links (two full)

Click here to Download DataSheet or here to Register to Download Manuals

FAST-Xe PCI-EXPRESS BOARDS

INTRODUCTION

The Fast-Xe frame grabber series is for users who anticipate a demand for extreme I/O requirements or higher bandwidth, complex image processing and real-time fast storage in a cost effective platform. The base Fast-X, is a one-half raw-length PCI board with four GigE ports and/or three basic 85 MHz Camera Link Channels and more which provide input for the newest cameras as well as a header for adaptation of other high speed FastXinterfaces. The front end data is formatted and preprocessed by a FPGA before being sent to the memory subsection, processor, GigE interfaces or other outputs. Finally, the Fast-Xe interfaces to the host computer through a 4x PCIe interface for state-of-the-art data acquisition. Options include the addition of multiple(8) Serial ATA (SATA) 150 MB/sec interfaces for continuous high-speed data storage without the usual OS or PCI transfer delays.

FAST-Xe KEY SERIES FEATURES

The diagram below outlines the basic functional section of the FAST-Xe boards. These are:

  • Raw PCI form factor board with 1-2 GB dedicated high speed DDRAM for sustained real-time on-board storage
  • Collects data from up to three (six optional) asynchronous basic Camera (channel) Link channels
  • Camera Link Specification

    National Semiconductor Channel Link Datasheet (343 KB)

  • Programmable FPGA and memory subsystem for I/O interface configuration and processing
  • STRETCH 5610 configurable processor for processing, strage, GigE connectivity
  • PCIe x4 bus interface
  • Supported by standard firmware development tools, including fully optimized basic data manipulation, data formatting and image processing routines
  • Drivers for Windows® 2K/XP, Linux, and Solaris™

Click here to Download DataSheet or here to Register to Download Manuals

FAST-XDIG BOARDS

INTRODUCTION

The Fast-XDIG is a two thirds raw-length PCI board with two input connectors. Each connector supports 16 data bits, 10 general purpose inputs, and 6 general purpose outputs. Clock rates up to 166 MHz can be supported. All the inputs and outputs are connected to an FPGA on the board are essentially available for any purpose required by the interface. The front-end data is formatted and preprocessed by a FPGA before being sent to the memory subsection, processor, GigE interfaces or other outputs. Finally, the Fast-XDIG interfaces to the host computer through a 4 lane PCIe or PCI-X interface for state-of-the-art data acquisition. Options include the addition of multiple(8) Serial ATA (SATA) 150 MB/sec interfaces for continuous high-speed data storage without the usual OS or PCI transfer delays and four GigE ports.

FASTUXGA

FAST-XDIGPCI-X AND PCI EXPRESS FEATURES

  • Raw PCI form factor board with 1-2GB dedicated high speed DDRAM for sustained real-time on-board storage

  • STRETCH 5610 processor standard with 4 GigE interfaces for 100MBytes/sec per channel actual transfer I/O

  • Collects data from two connectors of up to 52 GP inputs, while providing 12 GP outputs, at up to 166 MHz.

  • Programmable FPGA for I/O interface configuration and processing

  • PCI-X or PCI-e x4 bus interface

  • Supported by standard firmware development tools, including fully optimized basic data manipulation, data formatting and image processing routines

  • Drivers for Windows™ XP/Vista, Linux and Solaris™

FAST-XDIG PCI-X BUS FEATURES

The diagram below outlines the basic functional section of the FAST-UXGA boards. These are:

  • Collects data from two connectors of up to 52 GP inputs, while providing 12 GP outputs, at up to 166 MHz.
  • Raw PCI form factor board with 1 GB dedicated high speed DDRAM for sustained real-time on-board storage
  • Programmable FPGA and memory subsystem for I/O interface configuration and processing
  • STRETCH 5610 configurable processor for processing
  • 133 MHz PCI-X bus interface
  • Supported by standard firmware development tools, including fully optimized basic data manipulation, data formatting and image processing routines
  • Drivers for Windows® 2K/XP, Linux, and Solaris™

Fast-XDIG PCI-X bus

OPTIONS

  • If sustained high-speed storage is desired up to eight SATA ports are available on the FAST-Xe version for JBOD or raided storage of hundreds to thousands of gigabytes of storage per card.
  • Four GigE I/O ports

FAST-XDIG PCI-EXPRESS BUS FEATURES

The diagram below outlines the basic functional section of the FAST-XDIG board. These are:

  • Collects data from two connectors of up to 52 GP inputs, while providing 12 GP outputs, at up to 166 MHz.
  • Raw PCI form factor board with 1 GB dedicated high speed DDRAM for sustained real-time on-board storage
  • Programmable FPGA and memory subsystem for I/O interface configuration and processing
  • STRETCH 5610 configurable processor for processing
  • PCIe x4 bus interface
  • Supported by standard firmware development tools, including fully optimized basic data manipulation, data formatting and image processing routines
  • Drivers for Windows® 2K/XP, Linux, and Solaris™

Fast-XDIG PCI-EXPRESS

OPTIONS

  • If sustained high-speed storage is desired up to eight SATA ports are available on the FAST-Xe version for JBOD or raided storage of hundreds to thousands of gigabytes of storage per card
  • Four GigE I/O ports
 

Click here to Download DataSheets or here to Register to Download Manuals

news sales support downloads systems pmc cards camera support software applications frame grabbers about us search site map privacy legal home search site map privacy legal home top of page site map search news sales support downloads systems pmc cards camera support software applications frame grabbers about us